- 您现在的位置：买卖IC网 > Sheet目录318 > CAT4238TD-GT3 (ON Semiconductor)IC LED DRVR WHITE BCKLGHT TSOT-5
CAT4238
Block Diagram
V IN
47 m H
C 1
SW
C 2
4.7 m F
1 MHz
Oscillator
Over Voltage
Protection
0.22 m F
V REF
V IN
300 mV
Enable
–
+
A1
R C
+
–
A2
PWM &
Logic
Driver
N 1
LED
Current
SHDN
Thermal
Shutdown
& UVLO
C C
R S
GND
Current
Sense
FB
Figure 2. Block Diagram
R 1
15 W
Device Operation
The CAT4238 is a fixed frequency (1 MHz), low noise,
inductive boost converter that provides a constant current
with excellent line and load regulation. The device uses a
high-voltage CMOS power switch between the SW pin and
ground to energize the inductor. When the switch is turned
off, the stored energy in the inductor is released into the load
via the Schottky diode.
The on/off duty cycle of the power switch is internally
adjusted and controlled to maintain a constant regulated
voltage of 0.3 V across the feedback resistor connected to the
feedback pin (FB). The value of the resistor sets the LED
current accordingly (0.3 V/R 1 ).
During the initial power-up stage, the duty cycle of the
internal power switch is limited to prevent excessive in-rush
currents and thereby provide a “soft-start” mode of
operation.
While operating from a Li ? Ion battery, the device can
deliver 20 mA of load current into a string of up to 10 white
LEDs. For higher input voltages, the LED current can be
increased.
In the event of an “Open LED” fault condition, where the
feedback control loop becomes open, the output voltage will
continue to increase. Once this voltage exceeds 40 V, an
internal protection circuit will become active and place the
device into a very low power safe operating mode where
only a small amount of power is transferred to the output.
This is achieved by pulsing the switch once every 6 m s and
keeping it on for about 1 m s.
Thermal overload protection circuitry has been included
to prevent the device from operating at unsafe junction
temperatures above 150 ° C. In the event of a thermal
overload condition the device will automatically shutdown
and wait till the junction temperatures cools to 130 ° C before
normal operation is resumed.
Light Load Operation
Under light load condition (under 2 mA) and with input
voltage above 5.0 V, the CAT4238 driving 10 LEDs, the
driver starts pulse skipping. Although the LED current
remains well regulated, some lower frequency ripple may
appear.
Figure 3. Switching Waveform V IN = 5.0 V,
I LED = 1.5 mA
http://onsemi.com
4
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CAT4240TD-GT3
IC LED DRVR WHITE BCKLGHT TSOT-5
CAT93C56XI
IC EEPROM 2KBIT 2MHZ 8SOIC
CAT93C66XI
IC EEPROM 4KBIT 2MHZ 8SOIC
CAT93C86LI-G
IC EEPROM 16KBIT 3MHZ 8DIP
CAT9532WI-T1
IC LED DRIVER LINEAR 24-SOIC
CAT9552HV6I-TG2
IC LED DRIVER LINEAR 24-TQFN
CAV24C02YE-GT3
IC EEPROM I2C SRL 2KB 8TSSOP
CAV24C04YE-GT3
IC EEPROM 4KB I2C SER 8TSSOP
相关代理商/技术参数
CAT4238TD-GT3
制造商:ON Semiconductor 功能描述:IC LED DRIVER BOOST TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BOOST, TSOT-23-5
CAT4238TDI-G
制造商:ON Semiconductor 功能描述:IC 10-LED DRIVER LOW NOISE BOOST
CAT4240
制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:6 Watt Boost LED Driver
CAT4240_0711
制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:6 Watt Boost LED Driver
CAT4240AEVB
功能描述:BOARD EVALUATION DPP CAT4240A RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:* 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD
CAT4240AGEVB
制造商:ON Semiconductor 功能描述:EVAL BD FOR LED DRIVER - Bulk 制造商:ON Semiconductor 功能描述:BOARD EVAL FOR CAT4240
CAT4240TD-GT3
功能描述:LED照明驱动器 High Voltage Boost 2 Watt RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
CAT4240TD-GT3
制造商:ON Semiconductor 功能描述:IC LED DRIVER BOOST TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BOOST, TSOT-23-5